- #ARISAKA TYPE 38 CARBINE REPRODUCTION STOCK INSTALL#
- #ARISAKA TYPE 38 CARBINE REPRODUCTION STOCK FREE#
Finish inserting the follower hinge pin.Īlternate Reassembly Instructions as suggested by R.
#ARISAKA TYPE 38 CARBINE REPRODUCTION STOCK INSTALL#
The round end of the lug should be pointing towards the from the the barrel.Ĩ3) Slide the upper band over the front sight.Ĩ8) Install the follower spring into the follower housing.Ĩ9) Figure 89 shows the correctly seated follower spring.ĩ1) Partially install the follower hinge pin.ĩ2) Pivot the follower down and this will depress the follower spring. They are normally staked into place and will be difficult to remove.ĥ3) Insert the ejector aligned as shown in figure 53.ĥ7) Attach the bolt stop to the trigger assembly.ĥ9) Figure 59 shows the assembled trigger from the side of the bolt stop.Ħ0) Operate the trigger to make certain it functions properly.Ħ3) Tighten the upper butt plate screw only partially.Ħ6) Tighten the upper butt plate screw fully.Ħ8) Install the upper screw on the side rear sling bar.Ħ9) Tighten the upper screw on the side rear sling bar.ħ0) Install the lower screw on the side rear sling bar.ħ1) Tighten the lower screw on the side rear sling bar.ħ3) Install the rear screw on the rear sling swivel.ħ4) Tighten the rear screw on the rear sling swivel.ħ5) Install the forward screw on the rear sling swivel.ħ6) Tighten the forward screw on the rear sling swivel.ħ7) Install the barreled receiver into the rifle stock.ħ8) Install the hand guard near the front of the barrel.ħ9) Slide the lower band over the front sight with the sling loop pointing to the left side of the rifle.Ĩ0) Place the lower band over the slot on the hand guard.Ĩ1) Slide the hand guard and the lower band until the lower band slides over the lower band spring and locks into place.Ĩ2) Not alignment of bayonet lug in figure 82. If necessary there are two trigger stud pins pictured in figure 52.
Because the band rests in a groove in the hand guard the hand guard will move forward as well.Ģ8) Remove the clamp and continue to tap the lower band and hand guard forward.Ģ9) Slide the lower band off of the barrel and remove the hand guard.ģ0) Separate the barreled receiver from the rifle stock.ģ1) Unscrew the upper screw on the side rear sling bar.ģ2) Remove the upper screw on the side rear sling bar.ģ3) Unscrew the lower screw on the side rear sling bar.ģ4) Remove the lower screw on the side rear sling bar.ģ6) Unscrew the rear screw on the rear sling swivel.ģ7) Remove the rear screw on the rear sling swivel.ģ8) Unscrew the forward screw on the rear sling swivel.ģ9) Remove the forward screw on the rear sling swivel.ĥ1) Separate the bolt stop front he trigger assembly.ĥ2) I do not recommend disassembling the trigger further unless necessary to replace broken or worn parts.
#ARISAKA TYPE 38 CARBINE REPRODUCTION STOCK FREE#
This leaves my hands free to remove the upper band.Ģ7) Using non-marring tools such as a wooden dowel and a mallet, tap the lower band forward. I compress the spring with the quick clamp. I have found that padded rubber, quick clamps are invaluable in disassembling firearms. Then I slowly compress the entire device in a vise.ġ5a) Once the tension is released, it is quite easy to drift out the retaining pin.ġ9) Remove the clip latch and clip latch spring.Ģ0) Separate the clip latch spring from the clip latch.Ģ3) Slide the forward band off of the end of the barrel.Ģ5) Swing the rear sight to the rear if it is not alreadyĢ6) Depress the lower band spring.
I had to sand/file the sides of the clothespin to fit in between the sides of the follower holder. I find that I don't have the finger strength or dexterity to compress the flat spring and pop out the retaining pin.ġ4a) I devised an alternative method using ½ of a wooden clothespin. Ted Jeoġ3a) This is perhaps the hardest and trickiest part of the Carcano rifle. If the guard is difficult to remove you can tap one side of the guard lightly followed by tapping the opposite side.ġ2) Slide back and out the follower housing assembly.ġ3) Push out the follower hinge pin and remove.ġ4) Separate the follower from the follower housing.ġ6) Remove the follower spring from the follower housing.Īlternate Disassembly Instructions as suggested by R. Make sure rifle is unloaded.Ģ) Remove bolt by pressing trigger and pulling bolt out of rifle.ĩ) Remove the guard.